






Valved Exhaust System for Audi R8 / R8 Spyder 42 5.2 V10 (2010-2013)
Configuration
Audi R8 42 Valved Exhaust, R8 Spyder 42 5.2 V10 (2010-2013)
Valves
Operated by remote control, factory-paired.
Estimated at 0.50 m from the outlet, 45°, 2,000 rpm with a warm engine. Allow ± 2 dB depending on the engine and measuring point. A 3 dB difference is audible in a direct comparison; 10 dB sounds roughly twice as loud.
Configuration guide
Sound intensity with the valves open, on a scale of 0 to 10.
| Configuration | Intensity |
|---|---|
| Decat manifolds + Rog cat-back | 10/10 |
| 100-cell sports catalytic converter + Rog cat-back | 9/10 |
| 200-cell sports catalytic converter + Rog cat-back | 8/10 |
| Rog cat-back only, factory catalytic converter retained | 7/10 |
| Factory exhaust, for comparison | 3/10 |
The Audi R8 / R8 Spyder 42 5.2 V10 exhaust in detail.
Valved exhaust for Audi R8 42 5.2 V10: this Audi R8 42 exhaust system is made to order from your VIN. Derived from the Lamborghini Gallardo’s, the R8 type 42’s V10 5.2 FSI is naturally aspirated and howls beyond 8,000 rpm. It develops 525 hp and 530 Nm, and is among the last engines of its kind ever built. We list the 2010 to 2013 model years for this cat-back; the V8 R8 42 and the facelifted R8 4S have their own system.
On a car like this one, the exhaust is not an accessory, it is the instrument. The V10 climbs with a unique sound progression, deep and menacing below 4,000 rpm, then higher and higher up to the red line. The factory system holds back part of the high harmonics; with the valves open, our valved cat-back releases them. With the valves closed, the supercar becomes a discreet GT.
The system is compact, as always on a mid-engined R8: silencer and valves attach with clamps and gaskets, without welding, in about two hours. If the R8 has factory valves, the system connects to their control; failing that, the Rog remote and its boot-mounted unit operate them.
Upstream, the “Manifold” option replaces the five-outlet manifolds on each bank, with their catalytic converters. On an R8 V10 taken out on the road, the 200-cell manifolds have the advantage of keeping emissions control; the 100-cell ones are accepted or not depending on the car and the rules in your country, and the decat version gives the freest sound. On a naturally aspirated engine, the gain remains modest, 3 to 8% with an ECU remap. For the same design, the titanium version weighs around 40% less than 304 stainless steel and accentuates the V10’s metallic note.
The sound, configuration by configuration
On our scale of 0 to 10, the Rog system alone, valves open, sits around 7: the configuration to start with. Beyond 7, the Manifold option also replaces the catalytic converter: the 200-cell sports version gives 8 to 9 out of 10, the decat version 10 out of 10.
Made from your VIN, fitted by your garage
Every system is made from your VIN and checked before production: it fits your Audi R8 5.2 V10 perfectly, with no welding, on the original mounting points. Fitting is done by the garage of your choice; after ordering, write to us with your order number and we will suggest three trusted garages near you. Allow 20 working days from order confirmation to delivery, with free shipping.
Audi R8 / R8 Spyder 42 5.2 V10 exhaust specifications.
| System type | Valved cat-back (valve exhaust), compact layout, built to your VIN |
|---|---|
| Vehicle and chassis code | Audi R8 type 42 5.2 V10, coupé and Spyder |
| Engine | 5.2 FSI, naturally aspirated V10, 525 hp and 530 Nm |
| Years | 2010-2013 |
| Materials and finishes | 304 stainless steel or titanium; titanium in brushed, gold or purple |
| Valves | Factory valve control if the car has it, otherwise the Rog remote |
| Manifold (option) | Manifolds with 200-cell or 100-cell catalytic converters, or decat |
| Fitting | Clamps and gaskets, no welding, about 2 hours |
| Manufacturing and delivery | Built to your VIN, 20 working days, free delivery |
| Warranty | 3 years, parts and workmanship |
Questions about the Audi R8 / R8 Spyder 42 5.2 V10 exhaust.
My R8 42 V10 dates from 2014: is it covered?
No, 2014 and 2015 are excluded for the cat-back, and 2009 is not covered for the manifolds. Your VIN nevertheless lets us look for a solution before you place an order.
What does an ECU remap bring to the R8 42 V10?
The cat-back does not need one. With the manifolds and a full ECU remap, we state 604 hp and 588 Nm for this 525 hp V10, a gain that remains measured on a naturally aspirated engine.
How does the R8 42 V10 present at vehicle inspection with this system?
Present it with the valves closed: the V10 regains the restraint it had when it left the factory. Cat-back only or 200-cell manifolds keep emissions control. 100-cell manifolds are judged according to the vehicle and your country’s rules.
Stainless steel or titanium for the R8 42’s V10?
304 stainless steel gives a full bass and stands the test of time. Titanium weighs around 40% less for the same design and accentuates the metallic note at high revs, with three possible finishes.
Coupé or Spyder: does the R8 42 V10 take the same system?
Yes. The R8 42 V10 coupé and Spyder take the same Rog system: same chassis, same V10 5.2, same clamp-and-gasket fitting. Your VIN is only used to confirm the version and model year before manufacturing.
Audi R8 / R8 Spyder 42 5.2 V10: Does a valved exhaust system drone?
No. With the valves closed, the gases flow through the whole rear silencer and the cabin stays calm at a steady speed. Our Rog exhausts are designed to avoid drone. Learn more: Why our systems stay calm on the motorway.
Audi R8 5.2 V10: factory valves or Rog valves?
If your Audi R8 5.2 V10 has factory valves, you can choose to keep them: the system arrives with their mounts in place, you refit them and they work as before, through the drive modes. With Rog valves, the system comes already fitted to the exhaust and is controlled by remote; open or closed, the valves stay in the chosen position. The small control unit goes in the boot or at the front and connects to the cigarette lighter socket, to ring terminals or directly to the battery: everything is pre-wired, nothing to cut, 10 to 15 minutes on average. The remote is shipped without a battery because of carrier rules: remember to fit one.
Rog expert guide
Audi R8 / R8 Spyder 42 V10 exhaust: which one to choose?
The first-generation V10 R8 has gone down in history: the 5.2 derived from the Gallardo, the body that redefined Audi, and values that are already climbing. Its factory exhaust dates from a less restrictive era, but it is still far...
In detail
Rog Advisor
A question about this exhaust?
Fitment, sound, catalyst, valves, delivery: the answer comes straight away, with your configuration in context.
The Rog Advisor is an automated assistant trained on our product pages and answers. For an important decision, write to us: we confirm by e-mail.
Unsure about your configuration? Talk to us before you order. We know your car. Write to us at contact@rogmotorsport.com: we reply in writing, in English, within 24 hours. Email us
Reviews imported from our previous system and translated from French; verified purchases carry the badge.
Rog presentation film: choosing your vehicle, Standard or Equal Length design, stainless steel or titanium, Z-Pipe, controlled valves, titanium and tip finishes, and support from choosing your configuration through to shipping.
THE Rog CRAFT
Our process.
From the first bend to the last check. The same care at every step.
-
Design
Designed for your vehicle.
Geometry matched to your model, carefully studied bends and precise mounting points. Everything starts with accurate design.
-
Manufacture
Crafted with precision.
Tube bending, part fitting and TIG welding: every joint receives the same care.
-
Finishing
Material, elevated.
The finish reveals the character of the metal. Stainless steel or titanium, depending on the options available for your vehicle.
-
Assembly
Every part in its place.
Components are assembled and adjusted. On valved systems, the mechanism is fitted, set up and tested.
-
Inspection
Check. Then approve.
Geometry, welds, connections and gas flow: the key points are inspected before shipping.
-
Shipping
Ready to join you.
Reinforced packaging protects your exhaust in transit. The final step before giving your vehicle a new voice.
Customer builds
Your videos & photos
The Rog lines fitted on our customers' vehicles, in real conditions.
- Builds
- 500+
- Brands
- 28
- Satisfaction
- 4,9
The journal
News & advice
Valved exhaust comparison for the Audi RS3 8Y
Which valved exhaust for an Audi RS3 8Y? The options compared (sound, material, valves) and the Rog system made to...
Read the articleFrom order to fitting of your Rog exhaust
Your Rog exhaust is made for your car, to its VIN. Here is what happens between your order and the...
Read the articleHow to configure your Rog exhaust
A Rog exhaust is configured in five decisions, always in the same order: sound, material, front section, valves, then looks....
Read the articleValved exhaust comparison for the Mercedes A45 W177
Which valved exhaust for a Mercedes-AMG A45 or A45 S W177? The options compared (sound, material, valves) and the Rog...
Read the articleValved exhaust comparison for the BMW M2 G87
Which valved exhaust for a BMW M2 G87? The options compared (sound, material, valves) and the Rog system made to...
Read the articleExhaust rules: what changes in 2026 and 2027 (Euro 7, noise cameras, MOT)
Euro 7, new-car noise, noise cameras, MOT and vehicle inspection, and models: what really changes in 2026 and 2027 for...
Read the articleChanging your exhaust: what inspections and approvals cost in 9 countries
What the periodic inspection and the check of a modification cost after changing your exhaust, in 9 European countries: official...
Read the articleIs a cat-back exhaust legal in Ireland? What the NCT checks.
A cat-back leaves your factory cat, sensors and OBD as they are; valves closed, very close to stock, valves open,...
Read the articleNo article matches this search.
All articles
