The Rog Journal

Getting your valved exhaust system registered in Germany: the Einzelabnahme.

8 min read

This article is written for: Germany. For your country: Is a cat-back exhaust legal in the UK? What the MOT checks.

Getting your valved exhaust system registered in Germany: the Einzelabnahme.

Updated on 23 October 2026.

Yes, registration (Eintragung) is possible through an Einzelabnahme (individual inspection), and we provide you with the documents for it. Here you will find out how the inspection works step by step, roughly what it costs and how to prepare well for your appointment at the TÜV, DEKRA, GTÜ or KÜS. The decision lies with the inspector: with the right configuration and complete documents, you give yourself the best possible chance.

Your vehicle.

Choose your model: we show you its exhaust, its options and the lead time.

We check compatibility with your VIN before manufacturing.

Contents 9
  1. The essentials.
  2. Why an Einzelabnahme.
  3. The Einzelabnahme step by step.
  4. What registration costs.
  5. Our documents for the TÜV.
  6. Give yourself the best possible chance.
  7. Austria and Switzerland.
  8. Frequently asked questions.
  9. Sources.

The essentials.

  • The process: Rog has no type-approval document, and that is deliberate: a type-approved system sounds almost like the original, and the valves give you both. Registration therefore goes through an Einzelabnahme with an officially recognised inspector (amtlich anerkannter Sachverständiger or Prüfingenieur).
  • Our documents: a technical data sheet (Datenblatt) and a manufacturer's declaration (Herstellererklärung) for your configuration, free of charge and on request.
  • The cost: as a guide, around 150 to 500 € for the inspection, the same again depending on the effort for a noise measurement, plus around 12 to 50 € at the vehicle registration office.
  • Our advice: keep the original valves, choose the resonator, keep the original catalytic converter and come to the appointment with the valves closed.

Why an Einzelabnahme.

A new exhaust system changes the sound of your car, and noise behaviour is part of the vehicle's operating permit (§ 19 para. 2 StVZO). If a part has its own approval, for example an ABE or an ECE “e” mark, that is sufficient (§ 19 para. 3 StVZO). For all other exhaust systems, the StVZO provides for a case-by-case inspection: an officially recognised inspector checks your car with the new exhaust system and records the result in an expert report (Gutachten, § 21 StVZO).

This Einzelabnahme is now the intended route for any replacement exhaust system without ECE type approval. Since 20 June 2024, the KBA no longer issues new ABEs but Teiletypgenehmigungen instead, and it does not issue them for replacement silencers, which fall under European type approval. New Teilegutachten could only be issued until 19 June 2025. Since 2019, all inspection organisations have been able to carry out Einzelabnahmen: you have the choice.

The Einzelabnahme step by step.

  1. Request the documents. Using the “Unterlagen für den TÜV” button, request your technical data sheet and your manufacturer's declaration. You immediately receive a confirmation by email and the complete documents within 24 hours.
  2. Talk to the inspection centre. Before fitting, talk to the inspector who will carry out the inspection: show them our documents and ask about the measurements needed, an appointment and a quote.
  3. Fitting. The exhaust system bolts on to the original mounting points, at the garage of your choice.
  4. Appointment. Come with the car, the Zulassungsbescheinigung Teil I and our documents. The inspector examines the exhaust system and measures the noise if necessary. The reference is the production state: the original stationary noise level appears in box U.1 of the registration certificate, the measuring engine speed in box U.2. Depending on the scope, the appointment lasts from a few minutes to a few hours.
  5. Expert report. If all the technical requirements are met, you receive an expert report on the modification.
  6. Registration. With the expert report and the Zulassungsbescheinigung Teil I, you go to the vehicle registration office, which enters the modification in the vehicle papers.

What registration costs.

Each centre sets its own prices, depending on the effort. Published comparisons give these orders of magnitude:

Service Order of magnitude
Einzelabnahme (§ 21 StVZO) around 150 to 500 €
Noise measurement, depending on the effort around 150 to 500 €
Registration at the vehicle registration office around 12 to 50 €

These are orders of magnitude, not fixed prices: a second appointment or additional measurements increase the amount. Ask for a quote beforehand. Our documents cost you nothing.

Our documents for the TÜV.

For each exhaust system, we prepare two documents tailored to your configuration:

  • Technical data sheet: vehicle, material (stainless steel or titanium), exhaust system design, valve system, resonator and front section, with your VIN if you wish.
  • Manufacturer's declaration: it describes all the properties of the exhaust system, including the valve control, and confirms, for an exhaust system without a front section, that the original catalytic converter remains unchanged.

The documents are free, on request: with the “Unterlagen für den TÜV” button on each product page or directly here. You choose your configuration and give your email address, and your VIN if you wish. You immediately receive a confirmation by email and the complete documents within 24 hours.

Request your TÜV documents

Give yourself the best possible chance.

The inspector refers to your car's production state. We recommend this configuration to all customers who want to have their exhaust system registered:

  • Keep the original valves. If your car has original valves, choose the original valves option: we deliver the exhaust system with the mounts for your own valves, and the control stays as original, through the drive modes.
  • Otherwise, the Rog valve system. If your car has no valves, the Rog valve system is a good compromise: closed, close to the original sound; open, the full voice of your engine.
  • Choose the resonator. Just as sporty, a rounder and slightly softer voice, at the same price.
  • Order without the front section. The original catalytic converter stays, and emissions control remains as original.
  • Come with the valves closed. On inspection day, come to the appointment with the valves closed.
  • Declare everything. The inspector assesses the configuration you present: list all the parts, including the valve control, and present our documents.

The decision lies with the inspector. With this configuration and our documents, your appointment is perfectly prepared.

Austria and Switzerland.

Austria.

In Austria, after fitting, you report the modification to the Landesprüfstelle of your federal state (§ 33 KFG). According to the ÖAMTC, an exhaust of a different type from the original requires an E-Prüfzeichen or an entry in the vehicle's approval document. The authority obtains an expert's opinion, approves the modification and enters it in the approval database; if it affects essential characteristics of the type, an Einzelgenehmigung is required. Your papers are then up to date for the next § 57a KFG inspection (the Pickerl). Our documents are also valid for Austria; the Landesprüfstelle will tell you the cost.

Switzerland.

In Switzerland, you report the modification to the Strassenverkehrsamt of your canton. The car is inspected, and an approved modification is entered in the vehicle registration document (Fahrzeugausweis). According to FEDRO (ASTRA), replacement silencers must have an authorisation and be as effective as the original ones (Art. 53 OETV); for parts without approval for your vehicle type, you must show that the emissions and noise rules applicable at first registration are still met. First ask your Strassenverkehrsamt about the evidence required and its fees; our documents are also valid for Switzerland.

Frequently asked questions.

Can I have the exhaust system registered?
Yes, through an Einzelabnahme at the TÜV, DEKRA, GTÜ or KÜS. We provide the technical data sheet and the manufacturer's declaration for your configuration free of charge; the decision lies with the inspector.

Does Rog have an ABE or ECE type approval?
No, and that is deliberate: a type-approved system sounds almost like the original, and the valves give you both. Each exhaust system is made to order for your car, based on its VIN: the intended route is therefore the Einzelabnahme.

How much does registration cost?
As a guide, around 150 to 500 € for the inspection, the same again depending on the effort for a noise measurement, and around 12 to 50 € at the vehicle registration office. Your inspection centre will give you the exact price.

How quickly do I get the documents?
The confirmation arrives immediately by email, the complete documents within 24 hours.

Should the valves be open or closed at the appointment?
Closed. Tell the inspector about all the parts, including the valve control: they assess the configuration you present.

You will find your exhaust system among all Rog exhaust systems. We are happy to answer your questions about your configuration, quickly and personally.

Request your TÜV documents

Sources.

This page summarises the rules based on the following sources, all consulted on 23/10/2026 (claim-by-claim details in SOURCES.md). It does not replace the opinion of your inspection centre.

  1. § 19, § 21 and § 72 StVZO (gesetze-im-internet.de).
  2. KBA, FAQ “Umstieg auf die Teiletypgenehmigung”, May 2025; KBA, instruction on parts under § 22 StVZO, 15/04/2025.
  3. TÜV Rheinland, “Einzelabnahme” page.
  4. ADAC, “Geräusche von Pkw” information sheet, 01/2026.
  5. MOTORRAD, 15/02/2019 (end of the § 21 monopoly).
  6. AUTO ZEITUNG, 29/04/2025; KOSTENLUPE.DE, May 2026 (costs).
  7. § 33 and § 57a KFG (RIS); ÖAMTC; oesterreich.gv.at, 12/01/2026.
  8. ASTRA (FEDRO), “Lärmvorschriften für Personenwagen und Motorräder”; canton of Aargau, “Auspuffanlage”.