









Valved Exhaust System for Honda S2000 AP2 F22C / F20C (2004-2009)
Configuration
Honda S2000 AP2 Valved Exhaust F22C / F20C (2004-2009)
Valves
Operated by remote control, factory-paired.
Estimated at 0.50 m from the outlet, 45°, 2,000 rpm with a warm engine. Allow ± 2 dB depending on the engine and measuring point. A 3 dB difference is audible in a direct comparison; 10 dB sounds roughly twice as loud.
Configuration guide
Sound intensity with the valves open, on a scale of 0 to 10.
| Configuration | Intensity |
|---|---|
| Decat manifolds + Rog cat-back | 10/10 |
| 100-cell sports catalytic converter + Rog cat-back | 9/10 |
| 200-cell sports catalytic converter + Rog cat-back | 8/10 |
| Rog cat-back only, factory catalytic converter retained | 7/10 |
| Factory exhaust, for comparison | 3/10 |
The Honda S2000 AP2 exhaust in detail.
Valved exhaust for Honda S2000 AP2 F22C / F20C: this Honda S2000 AP2 exhaust system is made to order from your VIN. With the AP2, the S2000 adopted the F22C, a 2.2-liter naturally aspirated four-cylinder, or kept the F20C depending on the market. The F22C’s longer stroke takes away a little top-end reach but adds torque: 242 hp and 221 Nm, for the 2004 to 2009 model years. This system is designed for the AP2; the 1999 to 2003 AP1 has its own, and your VIN confirms compatibility before manufacturing.
No turbo to carry the sound: everything comes from the revs, and the most eagerly awaited moment remains the VTEC switching to its high cams. From the factory, the AP2 keeps it at a distance from the cabin. With the Rog valved cat-back, also known as a valved exhaust, the crisp mid-range tone gives way to a taut scream all the way to the red line, valves open; with them closed, the roadster adopts a civil voice for long stages.
With clamps and gaskets, without any welding, installation takes about two hours, and the valves are controlled via the factory switch if the AP2 has one, or via the two-button Rog remote.
Here the “Manifold” option replaces the original manifolds, shared by the AP1’s F20C and the AP2’s F22C: same cylinder head, same flange, same sensor. On this naturally aspirated engine, replacing them together with an ECU remap brings a real but modest gain of around 3 to 8%. In its 200-cell version, the part keeps the roadster’s emissions control, the 100-cell will be accepted or not depending on the car and the rules in your country, and the decat version gives the freest sound. The system comes in 304 stainless steel or titanium around 40% lighter, in brushed, gold or purple, with round tailpipes.
The sound, configuration by configuration
On our scale of 0 to 10, the Rog system alone, valves open, sits around 7: the configuration to start with. Beyond 7, the Manifold option also replaces the catalytic converter: the 200-cell sports version gives 8 to 9 out of 10, the decat version 10 out of 10.
Made from your VIN, fitted by your garage
Every system is made from your VIN and checked before production: it fits your Honda S2000 AP2 perfectly, with no welding, on the original mounting points. Fitting is done by the garage of your choice; after ordering, write to us with your order number and we will suggest three trusted garages near you. Allow 20 working days from order confirmation to delivery, with free shipping.
Honda S2000 AP2 exhaust specifications.
| System type | Valved cat-back (valve exhaust), built to your VIN |
|---|---|
| Vehicle and chassis code | Honda S2000, AP2 generation, roadster |
| Engine | F22C (or F20C depending on the market), naturally aspirated VTEC four-cylinder, 242 hp and 221 Nm |
| Years | 2004-2009 |
| Materials and finishes | 304 stainless steel or titanium; titanium in brushed, gold or purple |
| Valves | Factory valve control if the car has it, otherwise the Rog remote |
| Manifold (option) | Manifolds with 200-cell or 100-cell catalytic converters, or decat |
| Fitting | Clamps and gaskets, no welding, about 2 hours |
| Manufacturing and delivery | Made to order, 20 working days, free delivery |
| Warranty | 3 years, parts and workmanship |
Questions about the Honda S2000 AP2 exhaust.
My S2000 AP2 has kept the F20C: does the system suit it?
Yes: depending on the market, the AP2 received the F22C or kept the F20C, and the manifolds are shared by both engines. This system is designed for the AP2 from 2004 to 2009; we check your VIN before building.
Does the F22C of an S2000 AP2 need an ECU remap after fitting?
Not for the cat-back: VTEC keeps switching over just as from the factory. If you change the manifolds, an ECU remap can extract a gain of around 3 to 8%, consistent with a 242 hp naturally aspirated engine.
How should a modified S2000 AP2 be presented at vehicle inspection?
With the valves closed, for a voice close to stock, and factory or 200-cell manifolds, for intact emissions control. The 100-cell is judged according to the vehicle and the country’s rules.
Are the S2000 AP2 manifolds worthwhile on a naturally aspirated engine?
Yes, more than on a turbo: with no turbine downstream, their geometry acts directly on cylinder filling and on the VTEC scream. If only the voice interests you, the cat-back is enough; to tune the engine, manifolds and an ECU remap go together.
Honda S2000 AP2: Does a valved exhaust system drone?
No. With the valves closed, the gases flow through the whole rear muffler and the cabin stays calm at a steady speed. Our Rog exhausts are designed to avoid drone. Learn more: Why our systems stay calm on the highway.
Honda S2000 AP2: straight pipe or resonator?
On this model, two characters at the same price: the straight pipe for the raw sound of your engine, unfiltered, or the resonator for a rounder and slightly softer voice. Either way, the exhaust stays fully sporty. Learn more: Exhaust resonator: what does it do? Straight pipe or resonator, which sound to choose.
Honda S2000 AP2: factory valves or Rog valves?
If your Honda S2000 AP2 has factory valves, you can choose to keep them: the system arrives with their mounts in place, you refit them and they work as before, through the drive modes. With Rog valves, the system comes already fitted to the exhaust and is controlled by remote; open or closed, the valves stay in the chosen position. The small control unit goes in the trunk or at the front and connects to the cigarette lighter socket, to ring terminals or directly to the battery: everything is pre-wired, nothing to cut, 10 to 15 minutes on average. The remote is shipped without a battery because of carrier rules: remember to fit one.
Rog expert guide
Honda S2000 AP1 et AP2 exhaust: which one to choose?
The Honda S2000 was designed around an engine: a naturally aspirated four-cylinder with VTEC variable valve timing, able to rev higher than most sports cars of its era. The 1999 to 2003 AP1 and the 2004 to 2009 AP2 share...
In detail
Rog Advisor
A question about this exhaust?
Fitment, sound, catalyst, valves, delivery: the answer comes straight away, with your configuration in context.
The Rog Advisor is an automated assistant trained on our product pages and answers. For an important decision, write to us: we confirm by e-mail.
Unsure about your configuration? Talk to us before you order. We know your car. Write to us at contact@rogmotorsport.com: we reply in writing, in English, within 24 hours. Email us
Your country
Rog in the US.
State inspections and your exhaust
A Rog cat-back leaves your factory catalytic converters, oxygen sensors and OBD untouched, and valves closed, your car sounds very close to stock at inspection. Sport cats follow your state's rules, the catless version is for the track only, and your state decides.
On the road
Valves closed around town, your car sounds very close to stock, and you open them whenever you choose.
Your documents
Each system is built from your VIN, and we send its technical documentation free on request, for your state's inspection or for your insurer.
Your insurance
Some insurers ask you to declare aftermarket parts, so let yours know: our free technical documentation makes it easy.
Reviews imported from our previous system and translated from French; verified purchases carry the badge.
Rog presentation film: choosing your vehicle, Standard or Equal Length design, stainless steel or titanium, Z-Pipe, controlled valves, titanium and tip finishes, and support from choosing your configuration through to shipping.
THE Rog CRAFT
Our process.
From the first bend to the last check. The same care at every step.
-
Design
Designed for your vehicle.
Geometry matched to your model, carefully studied bends and precise mounting points. Everything starts with accurate design.
-
Manufacture
Crafted with precision.
Tube bending, part fitting and TIG welding: every joint receives the same care.
-
Finishing
Material, elevated.
The finish reveals the character of the metal. Stainless steel or titanium, depending on the options available for your vehicle.
-
Assembly
Every part in its place.
Components are assembled and adjusted. On valved systems, the mechanism is fitted, set up and tested.
-
Inspection
Check. Then approve.
Geometry, welds, connections and gas flow: the key points are inspected before shipping.
-
Shipping
Ready to join you.
Reinforced packaging protects your exhaust in transit. The final step before giving your vehicle a new voice.
Customer builds
Your videos & photos
The Rog lines fitted on our customers' vehicles, in real conditions.
- Builds
- 500+
- Brands
- 28
- Satisfaction
- 4,9
The journal
News & advice
From order to fitting of your Rog exhaust
Your Rog exhaust is made for your car, to its VIN. Here is what happens between your order and the...
Read the articleHow to configure your Rog exhaust
A Rog exhaust is configured in five decisions, always in the same order: sound, material, front section, valves, then looks....
Read the articleValved exhaust comparison for the Audi RS3 8Y
Which valved exhaust for an Audi RS3 8Y? The options compared (sound, material, valves) and the Rog system made to...
Read the articleValved exhaust comparison for the Mercedes A45 W177
Which valved exhaust for a Mercedes-AMG A45 or A45 S W177? The options compared (sound, material, valves) and the Rog...
Read the articleValved exhaust comparison for the BMW M2 G87
Which valved exhaust for a BMW M2 G87? The options compared (sound, material, valves) and the Rog system made to...
Read the articleExhaust rules: what changes in 2026 and 2027 (Euro 7, noise cameras, MOT)
Euro 7, new-car noise, noise cameras, MOT and vehicle inspection, and models: what really changes in 2026 and 2027 for...
Read the articleChanging your exhaust: what inspections and approvals cost in 9 countries
What the periodic inspection and the check of a modification cost after changing your exhaust, in 9 European countries: official...
Read the articleIs a cat-back exhaust legal in California? And in your state?
The sound you choose, and a quiet car when it matters: what you get with a Rog valved exhaust in...
Read the articleNo article matches this search.
All articles
